Jeep Wrangler: KEYS / Replacing The Battery In The Key Fob

The recommended replacement battery is CR2450.

NOTE:

  • Customers are recommended to use a battery obtained from Mopar®. Aftermarket coin battery dimensions may not meet the original OEM coin battery dimensions.
  • Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/ perchlorate for further information.
  • Do not touch the battery terminals that are on the back housing or the printed circuit board.
  • When a key fob battery is low, a warning will be indicated on the vehicle’s instrument cluster, and the fob LED will no longer illuminate with a button press.
  1. Remove the back cover of the fob by inserting a flat-blade screw driver into the slot on the bottom of the fob. Pry until the cover unsnaps being careful not to damage the seal. Proceed counterclockwise to pry the remaining snaps until the battery cover can be removed.

    Jeep Wrangler. Replacing The Battery In The Key Fob

    1-3 – Back Cover Pry Points

  2. Remove the depleted battery by inserting a small flat-blade screwdriver into the battery removal slot and sliding the battery forward and up being careful not to damage the electronic board underneath.

    Jeep Wrangler. Replacing The Battery In The Key Fob

    Battery Replacement

  3. Install the new battery into the key fob, making sure the positive (+) side is facing up. Slide the battery until it is seated securely below the tabs.
  4. Reassemble the back cover making sure it is properly aligned before snapping it back in place.

WARNING!

  • The integrated key fob contains a coin cell battery. Do not ingest the battery; there is a chemical burn hazard. If the coin cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.
  • If you think a battery may have been swallowed or placed inside any part of the body, seek immediate medical attention.
  • Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.

    KEY FOB

    Your vehicle is equipped with a key fob which supports Passive Entry, Remote Keyless Entry (RKE), Keyless Enter-N-Go (if equipped), and Remote Start (if equipped)...

    Programming And Requesting Additional Key Fobs

    Programming the key fob may be performed by an authorized dealer.NOTE: Once a key fob is programmed to a vehicle, it cannot be repurposed and reprogrammed to another vehicle...

    Other information:

    Jeep Wrangler 2018-2025 Owners Manual: Autostop Mode


    WARNING! Vehicles with the Stop/Start system will be equipped with two batteries. Both the main and the supplemental batteries must be disconnected to completely de-energize the 12 Volt electrical system. Serious injury or death could result if you do not disconnect both batteries...

    Jeep Wrangler 2018-2025 Owners Manual: To Install A LATCH-Compatible Child Restraint


    If the selected seating position has a Switchable Automatic Locking Retractor (ALR) seat belt, stow the seat belt, following the instructions below. Check what type of seat belt each seating position has. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily attach the hooks or connectors to the vehicle anchorages...

    Categories

    Manual Front Seat Forward/Rearward Adjustment

    The seat can be adjusted forward or rearward by using a bar located by the front of the seat cushion, near the floor. While sitting in the seat, lift up on the bar located under the seat cushion and move the seat forward or rearward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.

    Jeep Wrangler. Manual Front Seat Forward/Rearward Adjustment

    Adjustment Bar Location

    read more

     
    Copyright © 2025 www.jewrangler.com